Sequoia Top Airflow Guide

Thank you for purchasing the Top Airflow Sequoia from Humboldt Vape Tech. The TAF Sequoia is a fully customizable 25mm cannabis concentrate atomizer with adjustable top and bottom air flow, and a wide  variety of coil options. The TAF Sequoia is compatible with all Sequoia coils and it can be used with either top or bottom airflow.

PARTS OF THE TAF SEQUOIA

  • Mouthpiece
  • Top Cover
  • Top Airflow adjuster
  • Airflow down tube (used for top airflow)
  • Splash guard (used for bottom airflow)
  • Atomizer base with adjustable airflow
  • Coil (screws into atomize base)

READ ME

  • Select a compatible sub-ohm capable, 510 threaded box mod and battery/batteries.
  • Take the time to learn how to operate your box mod, including how to change mode, temp, etc.
  • Dry fire all new coils to burn off any residue
  • Do not overtighten the connections

TOP AIRFLOW SETUP

  • Screw the TAF Sequoia clockwise onto your box mod.
  • Remove the top cap by pulling it off the base of the Sequoia.
  • Remove the top airflow adjuster by pulling it off the top cover
  • Screw the airflow down tube clockwise into the top airflow adjuster
  • Screw the coil into the base of the Sequoia
  • Close the airflow holes onto the base
  • Twist the top airflow adjuster to you personal preference

BOTTOM AIRFLOW SETUP

  • Screw the TAF Sequoia clockwise onto your box mod
  • Remove the top cap by pulling it off the base of the Sequoia
  • Remove the top airflow adjuster and unscrew the Airflow down tube
  • Screw in the top airflow stopper into the top airflow adjuster
  • Press the top airflow adjuster and mouthpiece back onto the top cover
  • Screw the coil into the base of the Sequoia
  • Close the airflow holes on the top airflow adjuster
  • Adjust the airflow on the base to your personal preference

USAGE

  • Set the mod the the correct setting for each coil
  • Load a small amount of concentrate onto the coil near the center
  • Place the top cover back on the Sequoia
  • Inhale while pressing the fire button on your mod
  • mod settings may vary between models, use the following table as a guide and adjust to your personal preference

TIPS

  • Q-tips and isopropyl alcohol can be used to clean the Titanium bucket
  • When using the titanium bucket, allow the TAF Sequoia to cool off between sessions to keep the unit from getting too hot
  • Use a pulsing pattern when using wattage (power mode) to prevent burning your concentrates
  • Loading a small amount of concentrate will reduce reclaim and splatter
  • Store your Sequoia upright to prevent leaking
  • Lubricate O-rings with a food grade oil

CLEANING THE TAF SEQUOIA AND COILS

  • Unscrew the TAF Sequoia from the box mod
  • Remove the O-rings from the atomizer base and open all 4 air holes
  • Remove the O-rings from the mouthpiece and top airflow adjuster
  • Using 91-99% isopropyl alcohol, submerge and soak all parts
  • Rinse and repeat until the alcohol is clear and all parts are clean
  • Shake off excess alcohol and air dry until no alcohol remains
  • Once dry, put the O-rings back on and reassemble the Sequoia

*Do not use water to rinse or submerge the Sequoia or coils

 

Atomizer Coil Wattage (Power Mode) Temperature Control (TC)
Titanium Bucket

(Use TOP AIRFLOW & 10 second preheat)

24-28 W Ni Mode

24-28 W

400°F -450°F

13mm Ceramic Donut 15- 25W Ni Mode

25-35 W

350°F -450°F

Triple Titanium / Quartz 20-25 W Ti Mode

25-30 W

350°F -400°F

Triple Titanium / Black Ceramic 20-25 W Ti Mode

25-30 W

350°F -400°F

4mm Dual Twist Kanthal / Quartz 20-25 W
*Kanthal will only run on Wattage.

Leave a Reply

Your email address will not be published. Required fields are marked *